Astralpool / Hurlcon Impeller E230 Pump 40060K

Astralpool / Hurlcon Impeller E230 / E230C 40060K

This is the genuine Astralpool impeller, part number 40060K, for the Astralpool / Hurlcon E230 pool pump, including the later E230C. Astralpool lists the E230 at 1.0HP with a maximum flow of 230 lpm.

Dimensions & Specifications

• Diameter: 125mm
• Length: 89mm
• Vane Width (External): 11mm
• Vane Width (Internal): 5mm
• Mechanical Seal Type: 3/4" Type 6 Mechanical Seal

These measurements are approximate and can vary slightly due to manufacturing tolerances.

• Physically Stocked, unlike most "drop-shipping" websites.
• Shipped from VIC, NSW, WA, QLD

The E-Series Model Rule (rev. ESR-1.0)

Astralpool's parts lists give each E-Series model its own impeller, so the impeller has to match the model on the pump label. Work through these steps before ordering:

1. Read the model on the pump label: E140, E170, E230 or E290. Astralpool's current parts list shows later models with a C suffix, for example E230C.
2. Match the model to the table below.
3. Order the impeller listed for your model. Do not fit an impeller from another model to change the flow.
4. If the label is unreadable, send us photos of the pump label and the old impeller. We would rather identify it for you than have it come back.

Which E-Series Impeller Do I Need?

Sources: Astralpool E-Series spare parts sheet (2014), 2018-19 catalogue and current E-Series parts list, with the E290 from the 2019-20 catalogue. 40060M is also sold as an E140 / E170 impeller, so if you have an E140, send us photos of the pump label and old impeller and we will confirm the part before you order.

Fit a New Mechanical Seal at the Same Time

The pumps this impeller fits use the 3/4" Type 6 mechanical seal, part PS3868. Earlier Astralpool catalogues list the same seal as 75508.

The two seal faces separate when the impeller is removed from the motor shaft, and a disturbed seal can leak under the pump once it is back in service. We recommend fitting a new seal every time the impeller is changed.

Related Parts

• 40071A - diffuser, E-Series (buy here)
• 40165 - diffuser retaining screws (x2)
• 78187 - impeller bolt, nylon left-hand thread, listed for E-Series pumps (buy here)
• 78711 - o-ring listed with the impeller bolt (buy here)
• PS3868 - 3/4" Type 6 mechanical seal (buy here)

Symptoms of a Failed or Worn Impeller

• The motor runs normally but flow and filter pressure are down
• Noise or humming from the pump. Astralpool lists the impeller as a possible cause, along with the bearings, mechanical seal, capacitor and motor
• The pump will not run because debris is jammed in the impeller. Astralpool notes that a damaged hair and lint basket can let debris through to the impeller
• Vanes worn, chipped or cracked

If the impeller is jammed, check whether it can be freed before replacing it. Astralpool treats debris jammed in the impeller as general maintenance rather than a warranty fault, and warns that running a pump dry for any length of time causes severe damage.

Frequently Asked Questions

Will this fit an E140 or E170?
No. Astralpool's parts lists give 40060L for the E140 and 40060M for the E170.

Does it fit the E230C?
Yes. Astralpool's current E-Series parts list shows 40060K for the E230C.

Does the E-Series use an impeller retaining bolt?
Astralpool's current E-Series parts list includes impeller retaining bolt 78187 and o-ring 78711. If your pump has them, inspect both while the impeller is off and replace them if they are worn or damaged.

Do I need a new mechanical seal when I replace the impeller?
We recommend it. The seal faces separate when the impeller comes off, and a disturbed seal can leak once the pump is back in service. These pumps use the 3/4" Type 6 Mechanical Seal, part PS3868.

Is this a genuine Astralpool part?
Yes. We are an authorised Astralpool and Fluidra dealer and warranty agent, and this is the genuine 40060K impeller.

Manufacturer Catalogues, Diagrams & Part Numbers

Need exploded views, spare part numbers, product numbers or diagrams? See the manufacturer catalogue: Astralpool Catalogue 2026

Before ordering: confirm this part is correct for your pump. Use the catalogue above, seek professional assistance, or contact us with photos of your existing part, model details, serial numbers and any labels. As with all products, this must be diagnosed and fitted by a qualified and experienced person. This is a special-order item.

Common search terms: Astralpool 40060K, 40060 K, Hurlcon E230 impeller, E230C impeller, Astral E-Series pump impeller, E230 pool pump impeller, WWDG SpaPro.