{"product_id":"onga-pump-lid-o-ring-702208","title":"Onga Pump Lid O-Ring - LTP \/ PPP \/ 400 \/ 600 \/ 900 Series - 702208","description":"\u003ch3\u003eOnga Pump Lid O-Ring\u003c\/h3\u003e\n\u003cp\u003eThe o-ring that seals the screw-on strainer lid to the pump body on Onga LeisureTime, Pantera and the 400, 600 and 900 Series pumps. Replaces Onga part number \u003cstrong\u003e702208\u003c\/strong\u003e, also listed as \u003cstrong\u003e702208K\u003c\/strong\u003e. A flattened, perished or dried out lid o-ring is the most common reason an Onga pump will not prime or will not hold prime, because it draws air into the suction side rather than leaking water out.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"color: rgb(43, 0, 255);\"\u003e\u003cstrong\u003ePhysically Stocked, unlike most \"drop-shipping\" websites.\u003c\/strong\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: rgb(43, 0, 255);\"\u003e\u003cstrong\u003eShipped from VIC, NSW, WA, QLD\u003c\/strong\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFits These Pumps\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eOnga LeisureTime LTP\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLTP 400, LTP 550, LTP 750, LTP 1100\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eOnga Pantera PPP\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePPP 550, PPP 750, PPP 1100, PPP 1500, PPP 1500H\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eOnga series pumps with the screw-on lid\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e400 Series, 600 Series and 900 Series, the housings that take the 165mm screw-on lid\u003c\/li\u003e\n\u003cli\u003eBR Series\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eOnga is now part of Pentair, so the same pumps and the same parts are sold under both the Onga and Pentair names.\u003c\/p\u003e\n\u003ch3\u003ePart Numbers and Search References\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e702208 (Onga part number)\u003c\/li\u003e\n\u003cli\u003e702208K\u003c\/li\u003e\n\u003cli\u003ePA-592\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e approximately 147mm diameter with a 7mm section\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLid O-Ring Or Casing O-Ring?\u003c\/h3\u003e\n\u003cp\u003eThese pumps use two different o-rings and they are not interchangeable:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLid o-ring, 702208.\u003c\/strong\u003e This part. It sits in the groove on the clear strainer lid and seals the lid to the pump body. You can see it as soon as you unscrew the lid.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIf The Lid Itself Is Cracked\u003c\/h3\u003e\n\u003cp\u003eA new o-ring will not seal against a lid that is crazed, cracked or distorted around the sealing rim. In that case order \u003ca href=\"\/products\/sc-pa-392\"\u003ethe complete Onga LTP\/PPP pump lid, supplied with its o-ring\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eFitting Notes\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eClean the groove in the lid and the sealing face on the pump body before fitting. Grit on the face leaks air just as a worn o-ring does.\u003c\/li\u003e\n\u003cli\u003eLubricate with a silicone-based o-ring lubricant only. Petroleum jelly and mineral greases swell the rubber and destroy it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHand tighten the lid only.\u003c\/strong\u003e These lids seal on the o-ring face, not on thread tension. Levering the lid around with a tool or a strap wrench cracks the lid and does not improve the seal.\u003c\/li\u003e\n\u003cli\u003eIf the lid is hard to turn, lubricate the o-ring rather than forcing it. A dry o-ring grabs.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSymptoms Of A Failed Lid O-Ring\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePump will not prime, or loses prime after it shuts down\u003c\/li\u003e\n\u003cli\u003eAir bubbles visible in the strainer housing while the pump is running\u003c\/li\u003e\n\u003cli\u003eAir coming back to the pool through the returns\u003c\/li\u003e\n\u003cli\u003eWater weeping from under the lid when the pump stops\u003c\/li\u003e\n\u003cli\u003eAn o-ring that has gone hard, square sectioned, cracked or sticky\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eRunning a pump that is drawing air in past the lid will eventually damage the mechanical seal, so a leaking lid o-ring is worth attending to promptly.\u003c\/p\u003e\n\u003ch3\u003eRelated Onga LTP and PPP Parts\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/products\/sc-pa-392\"\u003eOnga LTP\/PPP pump lid, supplied with o-ring\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/sc-pa-395\"\u003eOnga LTP\/PPP skimmer pump basket\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/davey-sureflo-onga-lpt-ppp-poolrite-pump-compatible-unions\"\u003eUnions to suit Onga LTP and PPP pumps\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eNot Sure Which One You Need?\u003c\/h3\u003e\n\u003cp\u003eSend us a photo of your pump label and the old o-ring and we will confirm the part before you order. \u003ca href=\"\/pages\/contact-us\"\u003eContact us\u003c\/a\u003e if unsure.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eCommon search terms: Onga 702208, 702208K, Onga pump lid o ring, Onga LTP lid o ring, LTP400 LTP550 LTP750 LTP1100 lid seal, Pantera PPP550 PPP750 PPP1100 PPP1500 lid o ring, Onga 400 600 900 series lid o ring, BS431 o ring, PA-592, Onga pump not priming air leak, Pentair Onga lid seal.\u003c\/em\u003e\u003c\/p\u003e","brand":"Onga","offers":[{"title":"Default Title","offer_id":46981188714685,"sku":"PA-592 \/ 702208","price":12.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0372\/5253\/files\/onga-pump-lid-o-ring-ltp-ppp-400-600-900-series-702208-parts-534.webp?v=1793694787","url":"https:\/\/hasp.com.au\/products\/onga-pump-lid-o-ring-702208","provider":"Heater and Spa Parts","version":"1.0","type":"link"}